Electrical symbols and electronic circuit symbols are used for drawing schematic diagram.
The symbols represent electrical and electronic components.
Symbol | Component name | Meaning |
---|---|---|
Wire Symbols | ||
![]() |
Electrical Wire | Conductor of electrical current |
![]() |
Connected Wires | Connected crossing |
![]() |
Not Connected Wires | Wires are not connected |
Switch Symbols and Relay Symbols | ||
![]() |
SPST Toggle Switch | Disconnects current when open |
![]() |
SPDT Toggle Switch | Selects between two connections |
![]() |
Pushbutton Switch (N.O) | Momentary switch - normally open |
![]() |
Pushbutton Switch (N.C) | Momentary switch - normally closed |
![]() |
DIP Switch | DIP switch is used for onboard configuration |
![]() |
SPST Relay | Relay open / close connection by an electromagnet |
![]() |
SPDT Relay | |
![]() |
Jumper | Close connection by jumper insertion on pins. |
![]() |
Solder Bridge | Solder to close connection |
Ground Symbols | ||
![]() |
Earth Ground | Used for zero potential reference and electrical shock protection. |
![]() |
Chassis Ground | Connected to the chassis of the circuit |
![]() |
Digital / Common Ground | |
Resistor Symbols | ||
![]() |
Resistor (IEEE) | Resistor reduces the current flow. |
![]() |
Resistor (IEC) | |
![]() |
Potentiometer (IEEE) | Adjustable resistor - has 3 terminals. |
![]() |
Potentiometer (IEC) | |
![]() |
Variable Resistor / Rheostat (IEEE) | Adjustable resistor - has 2 terminals. |
![]() |
Variable Resistor / Rheostat (IEC) | |
![]() |
Trimmer Resistor | Preset resistor |
![]() |
Thermistor | Thermal resistor - change resistance when temperature changes |
![]() |
Photoresistor / Light dependent resistor (LDR) | Photo-resistor - change resistance with light intensity change |
Capacitor Symbols | ||
![]() |
Capacitor | Capacitor is used to store electric charge. It acts as short circuit with AC and open circuit with DC. |
![]() |
Capacitor | |
![]() |
Polarized Capacitor | Electrolytic capacitor |
![]() |
Polarized Capacitor | Electrolytic capacitor |
![]() |
Variable Capacitor | Adjustable capacitance |
Inductor / Coil Symbols | ||
![]() |
Inductor | Coil / solenoid that generates magnetic field |
![]() |
Iron Core Inductor | Includes iron |
![]() |
Variable Inductor | |
Power Supply Symbols | ||
![]() |
Voltage Source | Generates constant voltage |
![]() |
Current Source | Generates constant current. |
![]() |
AC Voltage Source | AC voltage source |
![]() |
Generator | Electrical voltage is generated by mechanical rotation of the generator |
![]() |
Battery Cell | Generates constant voltage |
![]() |
Battery | Generates constant voltage |
![]() |
Controlled Voltage Source | Generates voltage as a function of voltage or current of other circuit element. |
![]() |
Controlled Current Source | Generates current as a function of voltage or current of other circuit element. |
Meter Symbols | ||
![]() |
Voltmeter | Measures voltage. Has very high resistance. Connected in parallel. |
![]() |
Ammeter | Measures electric current. Has near zero resistance. Connected serially. |
![]() |
Ohmmeter | Measures resistance |
![]() |
Wattmeter | Measures electric power |
Lamp / Light Bulb Symbols | ||
![]() |
Lamp / light bulb | Generates light when current flows through |
![]() |
Lamp / light bulb | |
![]() |
Lamp / light bulb | |
Diode / LED Symbols | ||
![]() |
Diode | Diode allows current flow in one direction only - left (anode) to right (cathode). |
![]() |
Zener Diode | Allows current flow in one direction, but also can flow in the reverse direction when above breakdown voltage |
![]() |
Schottky Diode | Schottky diode is a diode with low voltage drop |
![]() |
Varactor / Varicap Diode | Variable capacitance diode |
![]() |
Tunnel Diode | |
![]() |
Light Emitting Diode (LED) | LED emits light when current flows through |
![]() |
Photodiode | Photodiode allows current flow when exposed to light |
Transistor Symbols | ||
![]() |
NPN Bipolar Transistor | Allows current flow when high potential at base (middle) |
![]() |
PNP Bipolar Transistor | Allows current flow when low potential at base (middle) |
![]() |
Darlington Transistor | Made from 2 bipolar transistors. Has total gain of the product of each gain. |
![]() |
JFET-N Transistor | N-channel field effect transistor |
![]() |
JFET-P Transistor | P-channel field effect transistor |
![]() |
NMOS Transistor | N-channel MOSFET transistor |
![]() |
PMOS Transistor | P-channel MOSFET transistor |
Misc. Symbols | ||
![]() |
Motor | Electric motor |
![]() |
Transformer | Change AC voltage from high to low or low to high. |
![]() |
Electric bell | Rings when activated |
![]() |
Buzzer | Produce buzzing sound |
![]() |
Fuse | The fuse disconnects when current above threshold. Used to protect circuit from high currents. |
![]() |
Fuse | |
![]() |
Bus | Contains several wires. Usually for data / address. |
![]() |
Bus | |
![]() |
Bus | |
![]() |
Optocoupler / Opto-isolator | Optocoupler isolates connection to other board |
![]() |
Loudspeaker | Converts electrical signal to sound waves |
![]() |
Microphone | Converts sound waves to electrical signal |
![]() |
Operational Amplifier | Amplify input signal |
![]() |
Schmitt Trigger | Operates with hysteresis to reduce noise. |
![]() |
Analog-to-digital converter (ADC) | Converts analog signal to digital numbers |
![]() |
Digital-to-Analog converter (DAC) | Converts digital numbers to analog signal |
![]() |
Crystal Oscillator | Used to generate precise frequency clock signal |
⎓ | Direct current | Direct current is generated from constant voltage level |
Antenna Symbols | ||
![]() |
Antenna / aerial | Transmits & receives radio waves |
![]() |
Antenna / aerial | |
![]() |
Dipole Antenna | Two wires simple antenna |
Logic Gates Symbols | ||
![]() |
NOT Gate (Inverter) | Outputs 1 when input is 0 |
![]() |
AND Gate | Outputs 1 when both inputs are 1. |
![]() |
NAND Gate | Outputs 0 when both inputs are 1. (NOT + AND) |
![]() |
OR Gate | Outputs 1 when any input is 1. |
![]() |
NOR Gate | Outputs 0 when any input is 1. (NOT + OR) |
![]() |
XOR Gate | Outputs 1 when inputs are different. (Exclusive OR) |
![]() |
D Flip-Flop | Stores one bit of data |
![]() |
Multiplexer / Mux 2 to 1 | Connects the output to selected input line. |
![]() |
Multiplexer / Mux 4 to 1 | |
![]() |
Demultiplexer / Demux 1 to 4 | Connects selected output to the input line. |