added ned folder for functional modules
created new file for perl based print engine and configuration for that engine

created new file for perl based print engine and configuration for that engine
configured and defined basic variables in configuration-module
started to introduce primitive samity-checks and configuration evaluation to printengime untill further notice onyl Beaglebone black with Lightcrafter 4500 on HDMI will be supported.
lautr3k · rkoeppl · rkoeppl · rkoeppl · rkoeppl · rkoeppl
Unified Split

Showing with 484 additions and 1 deletion.

+10 −1 js/main.js

+2 −0 modules/g1.gcode

+71 −0 modules/printengine.cfg

+354 −0 modules/printengine.pl

+47 −0 modules/send.pl
diff --git a/js/main.js b/js/main.js
@@ -454,7 +454,16 @@ function startSlicing() {
     if (settings.get('slicer.zip')) {
         zipFile   = new JSZip();
         zipFolder = zipFile.folder('slices');
-        zipFile.file("README.txt", 'Generated by SLAcer.js\r\nhttp://lautr3k.github.io/SLAcer.js/\r\n');
+	ontime = parseInt(times.on);
+	offtime = parseInt(times.off);
+	layerheight=settings.get('slicer.layers.height');
+	zipdelimiter='\"'
+	ziptext1= '#Generated by SLAcer.js\r\n#http://lautr3k.github.io/SLAcer.js/\r\nlayer_height='+zipdelimiter+layerheight;
+	ziptext2='\r\nexposure_time='+zipdelimiter+ontime;
+	ziptext3= '\r\nresin_settling_time='+zipdelimiter+offtime;
+	ziptext= ziptext1+zipdelimiter+ziptext2+zipdelimiter+ziptext3+zipdelimiter;
+	
+        zipFile.file("README.txt",ziptext);
     }
 
     slicesNumber && slice();
diff --git a/modules/g1.gcode b/modules/g1.gcode
@@ -0,0 +1,2 @@
+G28 Z
+G1 Z30 F30
diff --git a/modules/printengine.cfg b/modules/printengine.cfg
@@ -0,0 +1,71 @@
+#Configuration file for printengine.pl to be called by SLAcer.js and other printer services
+#Copyright 2016 Robert Koeppl, Fablab Leoben robert.koeppl@fablab-leoben.at
+#http://www.fablab-leoben.at
+#http://www.github.com/fablab-leoben
+#released under the GPL v2
+#this piece of software is provided with absolutely no warranty
+#use at your own risk
+log_file = "../log/printengine.log"
+temporary_folder="./temp"
+logging_enabled="TRUE"
+#controllerboard="BBB"
+controllerboard="raspiarduinoramps"
+arduinotty="/dev/ttyACM0"
+arduinottybaudrate="115200"
+steps_per_mm="100"
+#steps needed to move the Z-Axis 1mm
+projector_type="Lightcrafter4500"
+#default Light engine
+projector_usb_device="/dev/ttyUSB0"
+endstop_Z_max="TRUE"
+endstop_Z_max_type="NC"
+#NO="Normally Open", NC="Normally Closed". NC is preferred
+endstop_Z_min="TRUE"
+endstop_Z_min_type="NC"
+#NO="Normally Open", NC="Normally Closed". NC is preferred
+wiper="FALSE"
+door_contact="TRUE" 
+#Defines if there is a door contact to determine if the enclosure is closed
+X_pixels="912"
+Y_pixels="1140"
+Z_speed="5"
+#mm/s
+Z_max_speed="10"
+#mm/s
+Z_Autocal="True"
+#Automatically determine Z-travel by triggering both endstops and dividing the Distance
+overshoot="2"
+#overshoot in mm to make sure the whole area is covered in resin correctly
+testrun_capable="true"
+#Capability to run testruns with wavelengthe that do not trigger polymerisation
+testrun_color="RED"
+#Color channel used for test run
+prodrun_color="BLUE"
+#Color Channel used for production run
+vat_heatable="false"
+vat_target_temperature=""
+#Vat temperature in Celsius
+check_vat_presence="false" 
+#board specific configuration for Beaglebone Black
+virtual_terminal="1"
+display_software="builtin"
+#default is the builtin functionality support for other methods not implemented yet. fbi as other option planned next
+display_device="/dev/fb0"
+#PIN asignment
+pin_zmin="testpin"
+pin_zmax="testpin"
+pin_wiper_min="testpin"
+pin_wiper_max="testpin"
+pin_door="testpin"
+pin_step_Z="testpin"
+pin_enable_Z="testpin"
+pin_direction_Z="testpin"
+pin_trigger_pre="testpin"
+pin_trigger_post="testpin"
+pin_enable_wiper="testpin"
+pin_dir_wiper="testpin"
+pin_step_wiper="testpin"
+pin_vat_heater="testpin"
+pin_vat_temperature="testpin"
+pin_vat_presence="testpin"
+#end of BBB specifics